Comp-cams 3135KT Adjustable Fuel Pump Eccentric Manuel d'utilisateur télécharger pdf

Ford Roller Timing Set

With Adjustable Fuel Pump Eccentric

(Part # 3108KT, 3121KT, 3135KT)

Thank you for choosing COMP Cams® products; we are proud to be your manufacturer of choice.

Please read all of these instructions carefully before beginning installation and also take a moment to

review the included limited warranty information.

Note: The installation procedures which follow

assume that the engine has been disassembled

and cleaned as it would be for a timing set change.

Installation Instructions

1. Prepare the Engine. Loosen all rocker arms so that the camshaft can rotate freely.

2. Clean everything! Make sure that the engine mounting surfaces and timing set components are as

clean as possible. The life of the chain and sprockets depends on it.

3. Install the Dowel Pin. If you engine original used the two-piece fuel pump eccentric and the short

dowel pin, remove the old down pin. Press the new dowel pin into place, making sure that it is

fully seated in the camshaft. Note: Some older engines have a spacer on the camshaft and a

camshaft sprocket which is flat on the back. If your engine has one of these spacers, remove and

discard it. The new camshaft sprocket has the spacer machined in it.

4. Align the Engine. Rotate the crankshaft until the number one piston is at top dead center. The

crankshaft key should be pointing straight up. Rotate the camshaft until the dowel pin is pointing

straight down.

5. Assemble the Timing Set. Select the appropriate keyway and timing mark on the crankshaft

sprocket for the camshaft timing baseline desired. We recommend the standard timing position,

which uses the round timing mark and round keyway. Loop the chain over the camshaft sprocket.

Align the camshaft and crankshaft timing marks and loop the chain around the crankshaft sprocket.

Lift the sprocket and chain assembly into place on the camshaft and crankshaft. Slide the

crankshaft sprocket onto the crankshaft, while sliding the camshaft sprocket onto the camshaft.

Make sure that the sprockets are fully seated on their shafts.

6. Install the Fuel Pump Eccentric. Install the eccentric onto the camshaft sprocket making sure that

the dowel pins fully engage the proper holes in the eccentric. Install the proper bolt and washer

(supplied) and thread it all the way in, but leave it slightly loose. Check for clearance between the

washer and the dowel pin. If the washer touches the pin, remove the pin and grind one end until the

pin will no longer protrude through the eccentric, then re-install the dowel pin. The adjustable fuel

Tools & Supplies Needed:

o Torque Wrench

o Degree Wheel (Part #4791)

o Assembly Lube or Camshaft Lube (Part #154)

o Thread Locking Compound (Lock-tite)

Part # 150

Revised 12/6/04

1 2

Installation Instructions 1

Résumé du contenu

Page 1 - Installation Instructions

Ford Roller Timing Set With Adjustable Fuel Pump Ecc

Page 2

pump eccentric is infinitely adjustable so you can fine adjust your engine’s camshaft timing to exactly where you want it. 7. Adjust the Camshaft Ti

Commentaires sur ces manuels

Pas de commentaire

Comp-cams 3135KT Adjustable Fuel Pump Eccentric Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Comp-cams 3135KT Adjustable Fuel Pump Eccentric. COMP Cams 3135KT Adjustable Fuel Pump Eccentric User Manual [cs] [pl] [en] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Comp-cams 3135KT Adjustable Fuel Pump Eccentric